Search results
Jump to navigation
Jump to search
Create the page "C22C38/10" on this wiki! See also the search results found.
- ...), nitrogen (up to 200 ppm), silicon (up to 0.10%), and manganese (up to 0.10%). ...00; and, as optionals al 0-0.1; cr 0.0-1.0; n 0-200 ppm; si 0-0.10; mn 0-0.10, and a balance of fe and unavoidable impurities.3 KB (399 words) - 06:53, 12 September 2024
- [[Category:C22C38/10]] [[Category:C22C38/12]]3 KB (365 words) - 15:23, 3 December 2023
- [[Category:C22C38/00]] [[Category:C22C38/02]]5 KB (666 words) - 04:47, 26 July 2024
- * The ratio of chromium to niobium (c/nb) may range from 0.10 to 1.80. ...r more and 1.50 mass % or less; and impurities. in addition, c/nb may be 0.10 or more and 1.80 or less, where c/nb is a ratio of the content of c to the3 KB (432 words) - 04:50, 11 April 2024
- ...iod greater than or equal to about 1 second to less than or equal to about 10,000 seconds to from a precursor steel sheet; air quenching the precursor st [[Category:C22C38/48]]3 KB (442 words) - 10:13, 4 December 2023
- [[Category:C22C38/50]] [[Category:C22C38/46]]5 KB (760 words) - 11:18, 25 January 2024
- ...d Ti-based precipitate grains having a grain diameter less than 0.09 μm is 10 or more grains per 100 μmin a sheet cross section. [[Category:C22C38/00]]4 KB (595 words) - 04:46, 26 July 2024
- ...the Nb content is between 0.05% and 1.50%. The C/Nb ratio can range from 0.10 to 1.80. ...r more and 1.50 mass % or less; and impurities. In addition, C/Nb may be 0.10 or more and 1.80 or less, where C/Nb is a ratio of the content of C to the3 KB (451 words) - 08:29, 12 April 2024
- ..., an average aspect ratio of 1.20 or less, and an average particle size of 10 μm or more and 40 μm or less. In the amorphous alloy soft magnetic powder [[Category:C22C38/00]]3 KB (456 words) - 02:51, 23 August 2024
- ..., an average aspect ratio of 1.20 or less, and an average particle size of 10 �m or more and 40 �m or less. in the amorphous alloy soft magnetic powd [[Category:C22C38/00]]3 KB (463 words) - 08:07, 22 August 2024
- == Top 10 Technology Areas == * [[:Category:CPC_C22C38/001|C22C38/001]] (Ferrous alloys, e.g. steel alloys (cast-iron alloys)8 KB (1,056 words) - 14:38, 21 July 2024
- [[Category:C21D8/10]] [[Category:C22C38/00]]4 KB (555 words) - 08:26, 25 March 2024
- == Top 10 Technology Areas == * [[:Category:CPC_C22C38/54|C22C38/54]] (No explanation available)8 KB (921 words) - 04:29, 16 July 2024
- * Difference in Vickers hardness between the edge and center is 10 to 100 Hv ...e in ductile brittle transition temperature between the edge and center is 10 to 100°C4 KB (538 words) - 08:26, 25 March 2024
- == Top 10 Technology Areas == * [[:Category:CPC_C22C38/06|C22C38/06]] (No explanation available)11 KB (1,366 words) - 06:42, 16 July 2024
- ...is 7.0 µm or less, with a dislocation density ranging from 1.0×10^6 to 6.0×10^6 m. [[Category:C22C38/04]]4 KB (609 words) - 14:05, 15 July 2024
- == Top 10 Technology Areas == * [[:Category:CPC_C22C38/001|C22C38/001]] (Ferrous alloys, e.g. steel alloys (cast-iron alloys)11 KB (1,412 words) - 06:37, 19 July 2024
- [[Category:C22C38/00]] [[Category:C22C38/10]]3 KB (516 words) - 11:12, 15 July 2024
- ...an area fraction of ferrite: 40% to 85%, tempered martensite and bainite: 10% to 55% in total, retained austenite: 3% to 15%, and ferrite, tempered mart [[Category:C22C38/04]]3 KB (510 words) - 14:05, 15 July 2024
- == Top 10 Technology Areas == * [[:Category:CPC_B22F2998/10|B22F2998/10]] (Processes characterised by the sequence of their steps)9 KB (1,133 words) - 05:35, 29 July 2024